如何了解滑觸線常見故障處理方�
一、滑觸線斷電
A sliding contact line power,
主要原因:電刷在�(dǎo)管中爬坡;電刷磨損嚴�,無法觸及導體;�(dǎo)體接頭不平整;單集電器使用;�(dǎo)軌接頭松��
The main reason: brush in the conduit climbing; brush wear serious, can not touch the conductor; the conductor joint roughness; single collector; rail joint loosening.
處理方法:檢測集電器是否磨損嚴重,更換集電器;更換電�;重新調整連接節�;采用雙刷集電器;重新調整擰緊連接螺釘�
Treatment methods: detection of collector is badly worn, replace the collector; Replacement Brush; re adjust the connection; with double brush collector; re adjust, tighten the screw connection.
�、導軌變�,集電器運動受阻
Two, rail deformation, collector movement blocked
主要原因:環境溫度過�;提掛架間距大或松脫�
The main reason: the high ambient temperature; lifting rack spacing or loose.
處理方法:局部采用隔熱板,室外加遮陽板;增加滑觸線提掛架�(shù)�,矯正導�,并擰緊螺釘�
Processing method: partial use of insulation board, outdoor and visor; increase the sliding contact wire rack number provided, correct catheter, and tighten the screws.
�、工作時滑觸線晃動大
Three, work of sliding contact line shaking big
主要原因:撥叉無法吸收傳動誤�;導軌正線直線度�;提掛架松動�
The main reason: fork cannot absorb transmission error; rail line straightness deviation; lifting rack loose.
處理方法:修正牽引器,使之能自由吸收傳動誤差;調整導軌直線度;擰緊提掛架螺釘�
Treatment methods: fixed traction device, which can free free absorption, transmission error; the adjusting guide rail straightness; tighten screws lifting rack.
�、電刷磨損快
Four, brush wear quickly
主要原因:接頭不平整;載流量過大;彈簧壓力大�
The main reason: joint roughness; carrying capacity is too large; the spring pressure.
處理方法:按要求重新連接�(dǎo)軌;增加集電器數�;更換、修正彈簧壓��
Processing method: according to the requirement of re connected with the guide rail; increase the collector number; replacement, correction spring pressure.
五、電刷側面擦�
Five, brush side abrasion
主要原因:電刷磨�,滑觸線集電器定為不�;牽引器的撥�?zhèn)攘鬟f過大�
The main reason: brush wear, sliding touch line collector for it; the shifting fork side force of the tractor transmission is too large.
處理方法:更�、修正彈簧壓力;更換牽引撥叉或修正牽引器撥叉�
Processing method: replacement, correction spring pressure; replace the traction fork or modified tractor fork.
�、導軌內有火�
Six, rail spark
主要原因:電刷表面與�(dǎo)軌接觸不��
The main reason: brush the surface in contact with the rail side.
處理方法:檢測導軌接�,適當磨合電刷保�60%接觸面積�
Treatment methods: detecting the rail joint, appropriate running in brush to ensure 60% contact area.
�、滑觸線集電器行走有較大異響
Seven, the sliding contact line collector walking has large abnormal sound
主要原因:電流過大;接頭不平��
The main reason: the current is too large; joint roughness.
處理方法:增加集電器�(shù)量;重新安裝�(dǎo)軌連接�
Treatment methods: increase the collector number; re install rail connection.
八、滑觸線集電器外殼擦�
Eight, the sliding contact line collector casing abrasion
主要原因:導軌變�;集電器定為欠佳�
The main reason: rail deformation; collector for the poor.
處理方法:按故障2處理,增加定型夾;調整集電器�
Processing method: according to the fault treatment increased 2, shaping clamp; adjust the collector.
尊敬的客戶:
感謝您關注我們的�(chǎn)�,本公司除了有此�(chǎn)品介紹以�,還�滑觸�,安全滑觸�,扁平電纜,滑觸線指示燈等等的介�,您如果對我們的�(chǎn)品有興趣,歡迎來電咨�。謝�!